Model No.: TP09
TP09 TPMS product is designed for monitoring pressure and temperature of each tire of cars,
trucks, buses, OTR tires, etc. It will send out alarm in case of abnormal pressure and
temperature to users or drivers for safety driving. Furthermore, Using this TPMS product can
save fuel, prolong tires life and make driving more comfortable.
Solar Powered Wireless tire Pressure Monitoring System supporting trucks, trailers, buses
Features
Solar panel power
supply
Alert for
fast tire air leaking
Configurable for high
/ low pressure alert
USB charging if no solar
power source
High temperature resistant battery. battery in TPMS sensor: 120°C; battery in
TPMS display: 80°C
● Pressure and temperature alert
● Selectable pressure unit(PSI | BAR)
● Selectable temperature unit(°C | °F)
● Configurable for high / low temperature alert
● Easy sensor included in the monitor
● Automatic white and red backlight
● Rechargeable lithium battery
● Monitors up to 34 tires simultaneously
● External RF433.92MHz antenna
● Various TPMS sensors types: external type, internal type, banded type, air flow-through
type
Description
● Radial acceleration sensor, temperature sensor
● Embedded 8051 compatible 8-bit microcontroller
● 6KB on-chip FLASH memory
● 256Byte RAM
● 315 and 434MHz FSK/ASK RF-transmitter
● 125KHz ASK high-sensitivity LF-receiver
● Power control/wake-up system to minimize battery consumption
● Ultra low standby current
Compatible Vehicles Types:
car, van, bus, truck, trailer, etc.
TPMS Display Screen
the TPMS display can show 34 tires status including tire position, temperature, BAR/PSI unit, F
or C temperature unit, battery status, solar powered or not, temperature alert
indicator, tire pressure alert indicator.
Technical Properties:
Display Specs:
ITEMS
SPECIFICATIONS
Temperature Setting Range
-20°C--93°C
Operation Temperature
-20°C--80°C
Storage Temperature
-30°C--85°C
Power Supply
DC 5V
Frequency
RF433.92MHz
Battery
400mAh, 3.7v, High temperature resistant: 80+/-5°C. Check more...
Display
FSTN LCD(63*25/23*1.10Tmm), half penetration;
LED backlight: red and white SMD, 68*22*2.2mm
Size
87*73*35mm
Weight
82g
TPMS chip
ATA5428
Solar Power supply
0.35w power, 5V
Tire Pressure Sensors supported by our GPS tracking device and TPMS display
● Extend the life of the tire.
● Save your fuel consumption.
● Save your money.
● Control the tire pressure constantly.
● Release your attention from tire and more safety.
● No more tire break-ups due to running tires under inflated.
Packing Details(standard)
Standard accessories:
1 non slip mat | 1 RF433.92MHz external antenna
size:
TPMS Display Configuration
1. USB to serial driver cable
The USB to serial cable requires windows driver. Download from below link before any operation.
2. Set up the correct COM port for configurator
After driver has been installed, plug the USB cable into PC.
1. In Computer properties, go to 'Device manager'.
2. Expand 'Port (COM &LPT)', find 'USB-SERIAL CH340(C0M4)'.
CAUTION: 1. Port will only appear when USB to serial cable has plugged into PC.
2. COM4 is the number you will use for configurator manager.
3. COM port number will change in different PC and USB port.
4. Open the COM port when device is connecting with PC.
3. Interface Introduction-start up
This is the initial interface once Configurator Manager is running, if you got any error, please check
as below:
Make sure the .net framework 4 or above has been installed.
Make sure the USB to serial cable has been installed.
Make sure the COM Port is correct.
Section A:
This section is the window to display the configurator version (standard/beacon/COM/TP) and version
number (2.00).
Section B:
This section has provided some basic operation buttons and password input window to avoid access without
authorization.
Section C:
This is the section to flash the firmware of display.
Section D:
This is the most important window; it contains two sub tabs in this section. All the desired parameter
can be changed in this section.
Section E:
This section a log display window. The device will save the log continuously into a txt file and also
display in the log window.
Section F:
This is COM connection indicator, the communication between device and PC/laptop relies on the USB
connection. So please make sure the connection has been established.
3.1 Section A: Configurator version
3.2 Section B: Basic operation button
Read from dev: read the setting from device.
Save to dev: save the setting into device
Password: entry the password before any operation.
Initialize: reset to factory setting.
Reboot: reboot device
Import cfg file: import the device parameter from a XML file.
Export cfg file: export current setting into a XML file.
3.3 Section C: Firmware update
Load: load the firmware file.
Start: start to flash the firmware.
3.4 Section D: Parameter tab
This is main section where the device settings are changed.
3.4.1 Section D_sub: Setting
Basic Setup
EnterSleep Delay: the display will turn off in X seconds, if the vehicle is stop/no vibration.
ExitSleep Delay: the display will turn on in X seconds. If the vehicle is vibrating.
PressUnit: the pressure unit on the display.
TmepreatureUnit: Temperature unit on display.
Alarm Vlaue:
FrontTireHighAlarmValue: the maximum pressure for front tire alarm.
FrontTireLowaAlarmValue: the minimum pressure for front tire alarm.
rearTireHighAlarmValue: the maximum pressure for rear tire alarm
(if the number of the tire over than 4, this setting will work for all the rear tire.)
rearTireLowaAlarmValue: the minimum pressure for rear tire alarm.
(if the number of the tire over than 4, tis setting will work for all the rear tire.)
TemperatureHighAlarmValue: the maximum temperature for all tire.
3.4.2 Section D_sub: Alarm Value
Pressure unit: unit switch for KPa/PSI/Bar.
Receive all sensor data: device will display all received TPMS sensor data in the log window, not only
the one listed in
device.
TPMS ID: the sensor ID contains two part: position ID + original ID which print on the sticker. For
example, if you want
to install sensor '6C0C97FF' to the left side of 1st axle, position ID is 11. So 116C0C97FF should save
into
device.
CAUTION:
1. after all sensor has been stored inside the device, you should 'Read from dev' again, it this case,
all sensor will
match with the position icon.
2.if you want add/delete/change the position of the tire sensor, 'Read from dev' is required to let
sensor math with
position icon on the right side position diagram.
4. Operation example
4.1 How to change the front tire alarm?
1. Read from dev: read the setting from device first. Don't operate anything before you read from
device.
2. FrontTireHighAlarmValue: change the maximum desired value.
3. Save to dev: save the setting to device.
CAUTION: Open the COM port and entry the password before any operation.
4.2 How to export the device parameter to an external file?
1. Read from dev: read the setting from device first. Don't operate anything before you read from
device.
2. Change the desired setting.
3. Export cfg file: export the parameter setting file into a XML file.
4.3 How to quick set parameter for bath devices?
1. Import cfg file: load the setting from an external CFG file (XML file).
2. Import the XML file to device
3. Save settings to device.
CAUTION: Open the COM port and entry the password before any operation.
4.4 How to flash the display firmware?
1. Load: load the firmware.
2. Select the correct firmware from folder.
3. Start: start to flash the firmware.
4. CAUTION: Open the COM port and entry the password before any operation.
